Search results

Ok guys Ive tried to see if I would ever get her to run but I cant keep her any more. Her is the list she is a 92 TY engine bored .030 TRW forged pistons,Total seal race rings, Eagle rods, 4bolt mains, new valves,guides,spirngs, 50lb injectors, Ultimate chip for 50lbers, 13 guages (I know I went...

Ok guys I have a problem. I am trying to start the truck. It sat for about 2 years. If I put a volt meter on the injector connector I get voltage but if I put a "NOID" light I get no light. So she wont start. So what can I check. Im going to put the stock injectors back on and the stock chip and...

Ok I am broke.. No cash LOL... so I have a working 700r4 from a 89 GTA. I went to a junk yard and got a cross member from a 2wd s-10 and NOPE didnt work. So I need to know if anyone else has run into this problem. I need t get this tranny to hook up to this cross member. TIA

Hello all, My truck has been parked for 2 years. Now I have her ready to fire back up, I have injector pulse and I have spark, she will run for a second with a shot of carb clean. they are 50 lb injectors I got them from RPM a while ago I checked them with a meter and I got 12.3 ohms on each...

Hey guys Im sure its on here someplace but I cant find it, I need to know how to hook up the 3 wires for the resistors on the box. Im almost with the change over and thats all that is really holding me you. Just need to know which wire goes were? TIA

Has anyone had to replace one of these? Mine is oil soaked and has play. Need a new one. Any idea on how to order a new one? TIA Mike

Hey everyone, I need to know if there is a way to test my ECU with an ohm meter to see if I burnt my comp or just some wires.I did the ultimate jacka$$ think and put aluminum foil around the fuse and got that distinct smell of burning wire. So I have the truck 100 miles from me but I have the...

I have a t-72 ITS turbo with a PTE .86 housing I want a smaller houseing like a 60 or in the area but I need to know what trim I have. P-trim? S-trim? I have lag like hell. I have a 2800 9/11 and I want a better take off. any help will be awsome. TIA

Driving at about 80 my exhaust temp is 1200 with out boosting. Now the people who did the job for me but the sensor right behind the o2 sensor about an inch away. im not sure if im doing any damage. drove from Miami to SC with the water temp. not passing 190 deg. Truck ran great. so any info...

I just took off my head after runing it like 4 times. I want to know if I could use the same gasket again? TIA

I want ot change my heads I am really short on time. This my daily driver and I dont have time for a machine shop again. Do I have to have heads from a sy/ty or can I just use 92 4.3 heads? Its a 92 ty. I think I bent a valve I keep bending a pushrod in the same cylinder and I already changed...

took engine out just now cause there was a horrible noise comming from the oilpan. I took the car to a few people and they said by the sounds of the engine I spun a bearing. GREAT :evil: BUT I still had 50lbs of oil pressure. But the sound was bad . so when i removed thr flywheel from the motor...

I have been told by a few shops that Iv'e asked that if I want to upgrade my turbo. I was told a t3/t4 p trim .83 exhaust with a 60-1 front. they all say go with a Masterpower turbo. Havent heard much about them but they have used them on big horsepower engines and they say they kick ass? They...

Race proven motors has a set of 50# injectors e-bay I need a set but I want to know will they work with the ultimate v6 or 7 I know I have to send it back to Mike Lee to have him reprogram it. I have called him and also e-mailed him and no response. I'm sure he is busy so its no problom. I just...

I just bought a To4b with like a 1.52 exhaust housing I know its a huge turbo but my question is how hard will it be to adapt or make a flange for the mitsu to the Garrett. I have some one to make the down pipe and the wastegate on the crossover pipe. if anyone has done this any help will be...

what is the TRICK!!!! :evil: :evil: to put the oil pump sreen on. I have a new on ot install on my new oil pump and it is hard as hell. HELP!! TIA guys