17x10 questions, on all four corners

[IDRVSLO]

Okay so in my wheel searching I found a set that I like....for a good price. They are a 17x10 wheel with a 50mm offset. Will these work with the following setup on a lowered Sy? What issues might I run into.......I know the rears will be fine...more concerned with the front.

-5x4.75
-50mm
-275-40-17s on all 4 corners
-Direct bolt on the front
-25mm spacer on the rear

 

[abes_sy]

Re: 17x10 questions, on all four corners

I had the 17x9.5 zr1 wheels in the front and the only problem i had was that the wheel would rub the upper a arm when turning the wheel all the way to the left or right.

 

[IDRVSLO]

Re: 17x10 questions, on all four corners

Also will I be safe to run my 275 40 and 315 35s? I know the 315s will be pretty meaty on there, any thoughts would be appreciated.

 

[IDRVSLO]

Re: 17x10 questions, on all four corners

I had the 17x9.5 zr1 wheels in the front and the only problem i had was that the wheel would rub the upper a arm when turning the wheel all the way to the left or right.

Thanks!

If I remember correctly the ZR1 has a 56mm offset, so these being a 50mm they will have the same inner clearance. I should have just checked the offset calculator and compare it to the ZR1s...duh.

So with the rear spacer I will be sitting 13mm out in the rear and 16mm out in the front. In reality that is not bad at all. Now to run my 315/275 setup....hmmm. Either I get another 275 set or I just stick with these.

 

[gt67sy]

Re: 17x10 questions, on all four corners

I run 10.5 wheels up front with 295 tires but I have rpm tubular a-arms

 

[IDRVSLO]

Re: 17x10 questions, on all four corners

Wheels are going on tomorrow, I am sure with zero issues!

 

[canadian]

Re: 17x10 questions, on all four corners

Pics or it didn't happen

 

[Flyin Ryan]

Re: 17x10 questions, on all four corners

Pics or it didn't happen

x2

With stock a arms I say your going to be making allot of unwanted contact

 

[sychris]

Re: 17x10 questions, on all four corners

Also will I be safe to run my 275 40 and 315 35s? I know the 315s will be pretty meaty on there, any thoughts would be appreciated.

i run 275/40/17 all the way around . no spacers no rubbing in front maybe very little rubbing turning real hard . my wheels are 17x9.5 with 54 offset . i have spacers in rear

 

[IDRVSLO]

Re: 17x10 questions, on all four corners

x2

With stock a arms I say your going to be making allot of unwanted contact

Either way they never were installed. But if you used the calculator you would have seen that they would be further out from the inside then the ZR1 wheels are. So they would have fit better in regards to rubbing the A-arm.

The wheels showed up with one being bent beyond what is ever acceptable. Paypal claim was filed and I ended up grabbing a different set.

I hate people sometimes.

 

[Flyin Ryan]

Re: 17x10 questions, on all four corners

Either way they never were installed. But if you used the calculator you would have seen that they would be further out from the inside then the ZR1 wheels are. So they would have fit better in regards to rubbing the A-arm.

The wheels showed up with one being bent beyond what is ever acceptable. Paypal claim was filed and I ended up grabbing a different set.

I hate people sometimes.

Wow that sucks but glad you got your funds back painlessly through paypal and went with a different/better fitting wheel