Ninja 636 VS Deanzsyclone w Vid

[Grimgrak]

Re: Ninja 636 VS Deanzsyclone w Vid

I wouldn't be too worried running street bikes as they require a better surface to launch on than an awd.

 

[pinellas50]

Re: Ninja 636 VS Deanzsyclone w Vid

DAMN! It's been quite some time since I have seen a bike get spanked like that.

 

[mhoover]

Re: Ninja 636 VS Deanzsyclone w Vid

WOW! need i rewrite what i wrote in my PM dean?! LOL dang that thing sounds so good!!

BTW we had a 90 or so mm turbo, brodix heads, like Dean and every lbs over 20 it was estimated 50 HP every lb increase. so from 20-22 lbs of boost = 100 more HP. cant remember what size turbo dean has but i dont think 700 hp is out of the question if hes gonna run 9.50s or quicker.... just my uneducated opinion

MATT

 

[Deanzsyclone]

Re: Ninja 636 VS Deanzsyclone w Vid

WOW! need i rewrite what i wrote in my PM dean?! LOL dang that thing sounds so good!!

BTW we had a 90 or so mm turbo, brodix heads, like Dean and every lbs over 20 it was estimated 50 HP every lb increase. so from 20-22 lbs of boost = 100 more HP. cant remember what size turbo dean has but i dont think 700 hp is out of the question if hes gonna run 9.50s or quicker.... just my uneducated opinion

MATT

uneducated opinion, riiiigghht. :rotf: :rotf:

 

[mhoover]

Re: Ninja 636 VS Deanzsyclone w Vid

uneducated opinion, riiiigghht. :rotf: :rotf:

LOL LOL

MATT

 

[Deanzsyclone]

Re: Ninja 630 VS Deanzsyclone

Re: Ninja 630 VS Deanzsyclone

Good job, you should see if you can line up a race with a litre bike. :tup:

Soooo, jshu77 did you get around to seeing my race against the litre bike? :rotf:

 

[cameronsclone]

Re: Ninja 636 VS Deanzsyclone w Vid

Damn you took down an R1

 

[mrweelr]

Re: Ninja 636 VS Deanzsyclone w Vid

Nice kill. Man, wish I lived closer so I could race you on my dyno tuned '07 750. Are these guys you're racing typical squids or experienced riders who know how to get a good holeshot on a bike? Either way, your truck rocks Dean, be careful :tup:

 

[Syclone0565]

Re: test can you tell me?

Re: test can you tell me?

We need to see more videos in the DAYLIGHT

 

[JayLo]

Re: test can you tell me?

Re: test can you tell me?

We need to see more videos in the DAYLIGHT

+1 :tup:
________
Make a vaporizer

 

[ghettosled]

Re: test can you tell me?

Re: test can you tell me?

We need to see more videos in the DAYLIGHT

try this link if you haven't already seen it

http://sytyperformance.com/video/Deanlaunch.mov

 

[mhoover]

Re: Ninja 636 VS Deanzsyclone w Vid

COOOOOL! i miss our truck

MATT

 

[WyoSyclone]

Re: Ninja 636 VS Deanzsyclone w Vid

Wow Dean... just ran through these videos again.... amazing Sy! Looks like that last video may have been in Simi?

Just lookin' at the pics on your website... do you have disc brakes or C-clip eliminators in the rear?? Don't wanna pull a Doc on us!

 

[Deanzsyclone]

Re: Ninja 636 VS Deanzsyclone w Vid

Wow Dean... just ran through these videos again.... amazing Sy! Looks like that last video may have been in Simi?

Just lookin' at the pics on your website... do you have disc brakes or C-clip eliminators in the rear?? Don't wanna pull a Doc on us!

Close, it was in Ventura city. Out near golf course drive, after hours commercial area. Sorry to say the brakes are stock front and back, but got rid of the vacume system. I'll upgrade brakes in the near future, I like stopping. I'm going for a new alky kit within a month or so, then tune for that so I can run 25lbs with 91 octane. Can't wait :tup:

I do have to add though the stock brakes with the new system work MUCH bettern than before.

 

[WyoSyclone]

Re: Ninja 636 VS Deanzsyclone w Vid

Close, it was in Ventura city. Out near golf course drive, after hours commercial area. Sorry to say the brakes are stock front and back, but got rid of the vacume system. I'll upgrade brakes in the near future, I like stopping. I'm going for a new alky kit within a month or so, then tune for that so I can run 25lbs with 91 octane. Can't wait :tup:

I do have to add though the stock brakes with the new system work MUCH bettern than before.

Well, before then, just don't snap an axle and go in circles for us!
Man I miss living there!!

 

[cloneman315]

Re: Ninja 636 VS Deanzsyclone w Vid

dean is this truck going to the track soon i hope?

 

[Deanzsyclone]

Re: Ninja 636 VS Deanzsyclone w Vid

dean is this truck going to the track soon i hope?

Track is rather far away from me, and local authorities won't let a track be built in our area. Wonder why they street race out here :roll:

I still need to order, and install a new meth injection kit, and have it tuned, then I'll seek out a track to run at. Hopefully this year.

 

[Owned]

Re: Ninja 636 VS Deanzsyclone w Vid

Track is rather far away from me, and local authorities won't let a track be built in our area. Wonder why they street race out here :roll:

I still need to order, and install a new meth injection kit, and have it tuned, then I'll seek out a track to run at. Hopefully this year.

I have a tow truck! we can tow the beast! Nice kill! I wish I had cash on me the night against the "Ringer" sti. lol

 

[Deanzsyclone]

Re: Ninja 636 VS Deanzsyclone w Vid

I have a tow truck! we can tow the beast! Nice kill! I wish I had cash on me the night against the "Ringer" sti. lol

Tow truck would be reasuring to go down with, you know, just in case. Who are you? You the guy from the gastation on harbor with the new sy??
Ahh yes Dorian, hey buddy, man finaly a local syclone other than mine... You need to bring that thing over so I can take a look at it when its done.

 

[Owned]

Re: Ninja 636 VS Deanzsyclone w Vid

lol for sure, :lol: