Recent content by NZTY

  1. N

    Voltage F14

    Re: Voltage F14 WOW I really feel like an idiot. I found out that a had a bad terminal plug on F14, removed the terminal plug and stuck a wire onto the pin and batman problem solved. Now I can finally record wideband data and not just look at my display. Thanks for all your help guys.
  2. N

    Code 59 Partially Open.

    Re: Code 59 Partially Open. Name - Anthony Glasson * Truck, mods - typhoon, Unopened 60,000 mile motor, Garrett GT35, DIY A/A intercooler, Hi imp 50#, Fuel pump & reg, 3 inch exhaust. Vortecs and cam ready to install * Tuning equipment you have - Ostrich, Lc-1, tunerPro Rt. * Why do you want...
  3. N

    Voltage F14

    Re: Voltage F14 I get around 5.4 volts at the plug when disconnected from the ecm. I'm sure it is something simple but it is usually the simple things that are the hardest to find. I might try code 59, you never know! Thank for your efforts anyway and I'll let you know if i get it sorted.
  4. N

    Voltage F14

    Re: Voltage F14 I have Brown (analog out 2) in F14, green in F15, Blue in F13 and purple in E14. That sound correct? Yeah I want to get this sorted for 58 before I step up to 59. Thanks again.
  5. N

    Voltage F14

    Re: Voltage F14 Yes I have tried both the patched bins that were posted up a while back and ones I did myself, both with the same result. I am seeing voltage at the F14 pin and WB is grounded to B9. The external WB display works fines so I don't think there is a problem with the controller or...
  6. N

    Voltage F14

    Re: Voltage F14 I am still have the same issues after a second re-wire. I'm starting to go crazy thinking of 10.1 all the time.
  7. N

    Voltage F14

    Re: Voltage F14 Yeah I have been using my own patched bin and I also tried one of the posted ones, both with the same results. When connected to the ECM I'm getting a voltage at F14 that is proportional to the value of the Wideband output. Thanks for your help.
  8. N

    Voltage F14

    Re: Voltage F14 Ok so I disconnected the F14 wire and got voltage and then reconnected it an got voltage at the terminal, but still no reading on Tunerpro. I've got the LC-1 programmed to 0 volts @ AFR 10 and 5 volts @ AFR 20. The only thing is when I open up the programmer the LC-1 has...
  9. N

    Voltage F14

    The problem I have got is that the wideband reading does not get displayed in tunerpro.I have an external wideband display which I have been using to tune with for the past couple of weeks but I would like to have the tunerpro output as well. At one stage it was working but only for a min and...
  10. N

    Tunerpro / G1 Help

    Re: Tunerpro / G1 Help I finally got it all sorted. I changed the batteries in the Ostrich and which seems to have been the problem. Thanks a lot for your help and I will probably have some more questions once I get further along in tuning my truck. Anthony
  11. N

    Tunerpro / G1 Help

    Re: Tunerpro / G1 Help I'm using Ostrich which seems to be connecting just fine, bin is uploading to Ostrich. Does the Ostrich need to be programmed also? In Tunerpro the test for valid ALDL cable says the cable is valid. The stock memcal seems to be connected correctly also. Thanks again Anthony
  12. N

    Tunerpro / G1 Help

    The problem I'm having is that my ALDL cable works perfectly when the G1 adaptor is not connected however when it is connected I can't seem to get it to connect to the PCM with either Datamaster or Tunerpro. Any ideas? Thanks Anthony
  13. N

    International SyTy Check-In

    Re: International SyTy Check-In Hello Anthony from New Zealand Pics of TY :tup:
  14. N

    Hello from New Zealand

    Re: Hello from New Zealand Thanks alot for the comments. Hideakimura lets just say i found a way to keep it LHD :cool: Tony
  15. N

    Hello from New Zealand

    Hello Everyone Here is a few pic's of the TY in it's current state.I got it stock from Japan with a bad turbo and a leak in the intercooler along with a alot of other little promblems. PICS of TY Also a big thanks to SY/TY.net been a huge help with getting the TY back up running again. :syty...
Top