Search results

Mark Williams 4l80e to Borg Warner 4472 input shaft and Billet adapter with cap head bolts to bolt the 4L80E to your transfer case. Sold truck before upgrading to the 4L80E. Syclone Typhoon $900

Bought this Torsen type front limited slip differential from John Frey and sold the truck before I had a chance to install it. It is exactly as it arrived from John. I can have it shipped through R&L Carriers to your door as long as you have access on your street for a semi. If you do not you...

Bought this built 8.5 rear-end from John Frey and sold the truck before I had a chance to install it. Its a bolt in but will require you shortening your driveshaft 1 inch. Its set up for standard disc brakes. I have the parking brakes and calipers included in this sale. It has a Auburn Posi...

This 79k mile Typhoon is a survivor. There are not that many rust free trucks left out there. It spent its life in AZ. and then Calf. You could put this one back to factory if you chose to. It still has the original 4.3 and 700R4. Everything works inside including the factory radio. The factory...

Hello, I bought a 93 Typhoon and it already had the racetronx fuel pump hot wire kit installed. The main hot wire in the system runs up to the alternator. The harness has a male and female connector back up under behind the tank that plugs into the factory fuel pump harness making it a plug and...

Looking for a set of drivers seat brackets. Can not find any around here in the yards. Thank You Will

I have a LS swap pan and pickup sitting here I don't see me using in the near future. Anyone interested? Its the LS swap pan from RPM. $450

Any turbo LS/4L80E swapped Syclones out there for sale right now? Now that I have retired I am looking for another toy to add to the stable. Thanks Will

Looking for a factory wiring harness (C100). I know I can go to a pull-a-part yard and get one but I would rather buy one. Anyone? Cash in hand. Thanks

Looking for a nice used set or new set. Any ideas? Thanks

Update: No longer looking, Found One. Here is what I would like if there is one out there for sale. Clean Typhoon (Red a serious +) No rust (surface rust on frame ok) 4L80e conversion upgraded rods and pistons would be nice but can be a stock 4.3 If you or you know of someone with one...

I am looking for a complete factory wiring harness. Fuse block and all. If someone is parting out a Syclone ( or Typhoon - I guess its about the same) I will take it. Need it like yesterday. Can't seem to find one anywhere. Thanks Will :tup:

Hello, I am installing a complete new wiring harness into my syclone. I have everything hooked up except 3 things. I have the wiring diagrams for the Sy/Ty's but I can not figure out where I am going wrong on these plugs. I have the column hooked up have a couple questions for the wiring experts...

Have been looking for a Red typhoon for a while. Clean title, clean truck, Factory or lightly modded. CASH in hand :tup: Thanks Will

Saw this while surfing https://chicago.craigslist.org/wcl/cto/6008264866.html

Selling a Holley EFI harness for the 4.3. I already replaced the Knock and TPS ends so its ready to go. I plugged it in and started the truck before pulling it all out and switching to a full LSx build and Holley EFI Setup. This is what you need if your going to swap to the Holley EFI system...

* * * Buyer backed out - Back up for sale * * * Pulled all this out to start Project Executioner. (See build thread in LSx section) Below is the motor and parts list. Has less than 1500 miles on everything. I have every single receipt also if you would like to see any of them. 90% was...

Here is the DYNO video from yesterday. 94* and 70% humidity still made over 1000hp. I will post up the Dyno sheet once I receive it. Should be quite rowdy. https://vimeo.com/176748331

Pulled all this out to start Project Executioner. (See build thread in LSx section) Below is the motor and parts list. Has less than 1500 miles on everything. I have every single receipt also if you would like to see any of them. 90% was built and installed by RPM Motorsports. You can go...

Project Executioner Goal: To Build a reliable, high Hp/Tq, Stock Looking, Syclone capable of executing all street contenders Expected Results: 8's on street tires & 1500hp+ Time Frame: Stage One (1000hp) - 90 Days, Stage two (1200hp) - 14 Days, Stage three (1500+) - 30 Days...