How not to run 30psi boost! - Video added!

D

denny

Active member
I know after seeing autoaddiction 10 sec pass , no one really cares about my 11.5 :D , here they are anywhay.

Run1
http://www.youtube.com/watch?v=R1xLL9mfAuE
Run2
http://www.youtube.com/watch?v=Lo8oADyFRs4
Run3
http://www.youtube.com/watch?v=6yTCCNbpHWA



Etown on Sunday- $100 for test and tune only had money to buy for 3gal 116 + 1/2tank 93 - mod in my sig.
First run - PTE dump tube open, 23psi -
Wastegate can't handle the open dump, let off the gas after the laptop flashing RED, then get back on, also broke the front suspension limiter
60' 1.69
1/8 7.183 @ 96.87
1/4 11.53 @ 111.55

Datamaster.jpg

WIDEBANDRUN1.jpg


Second run - close dump - 23psi - had to let off the gas again, getting knock
just $50 JCWhitney traction bar
60' 1.77
1/8 7.49 @ 93.3
1/4 11.713 @ 116.81
DatamasterR2.jpg

logworks took a dump when I try to save.

Thrid run - Street timing setting ( 22 psi)
60' 1.746
1/8 7.473 @ 93.6
1/4 11.603 @ 118.23
DatamasterR3.jpg

WIDEBANDRUN3.jpg


"No motor was hurt in these proceedings" :D
 
Last edited:
sytyguy

sytyguy

Moderated User
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

Yeah, I remember the first time I scanned Tyson's truck - by 20 mph, DM was maxed until he let off @ 134 mph. His gauge said 31.5 psi.......gobs of meth and no knock. Sick stuff.

Hood
 
cloneman315

cloneman315

Active member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

shouldnt the voltage be a lil higher on the first datamaster?,mine was like that untill i did the voltage mod.
 
D

denny

Active member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

I check out my alky, from those run it dosen't seem to be working right. I think I will get the Devil's own controller, what I have now is not cutting it.

I never get above 12.9 volt at wot. When I do the 75lb and Phil chip, then I will voltage mod. I just need to get a modded ecm.
 
sy2207

sy2207

Donating Member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

It's hotwiring the battery direct to the ecm or at least from the wires under the steering column.

supersports10 said:
voltage mod???? eleborate please????
Click to expand...
 
S

SCWolverine

New member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

supersports10 said:
voltage mod???? eleborate please????
Click to expand...


Use the current ecm power feed to switch on a relay completing the connection between batt. & ecm (larger wire). Eliminates the small "dirty" factory wiring (and it's voltage drops).
 
supersports10

supersports10

New member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

SCWolverine said:
Use the current ecm power feed to switch on a relay completing the connection between batt. & ecm (larger wire). Eliminates the small "dirty" factory wiring (and it's voltage drops).
Click to expand...

hmmm.. i have the caspers v-plus voltage booster, that connectes to the tps, and the alt.

add'a 2 volts above 70% tps.:D
 
cloneman315

cloneman315

Active member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

as your injector dc gets high the voltage drops,and i believe it can change the whole tune,i picked up a little over a volt at the ecm,and i have a under drive pulley.
 
TT350

TT350

Manufacturer
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

It cost you a $100.00 for test and tune damn!!!
T&T is only $20.00 down here.
 
D

denny

Active member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

TT350 said:
It cost you a $100.00 for test and tune damn!!!
T&T is only $20.00 down here.
Click to expand...

Yep, test and tune on Sundays at Englishtown is $100, you get 6 runs. I think its either $30 or $40 on Wed and Fri. I found out that if I had run in a class (street class) I would get min 3 runs in for $40.

C116 was $9.xx a gal.

Plus had to drive 80 miles each way, $30 in tolls , had my wife and kids follow me with the minivan, double tools and gas.
 
Last edited:
JKsSyclone

JKsSyclone

Active member
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

TT350 said:
It cost you a $100.00 for test and tune damn!!!
T&T is only $20.00 down here.
Click to expand...

$100 !!!! :eek:
$10 here :dunno:
 
Flyin Ryan

Flyin Ryan

hated cuz he drives fords
Re: How not to run 30psi boost!

Re: How not to run 30psi boost!

SCWolverine said:
Use the current ecm power feed to switch on a relay completing the connection between batt. & ecm (larger wire). Eliminates the small "dirty" factory wiring (and it's voltage drops).
Click to expand...

Is there any kind of write up or step by step on this mod anywhere?
 
autoaddictions

autoaddictions

Active member
Re: How not to run 30psi boost! - Video added!

Thanks for postin your runs is nice to watch sombody else beat ther truck. 11.5s is no joke for your mods. Your intake temps are sweet you must be using meth mine are 200*plus. I too am going to install meth soon. You go any faster, just like Ralph and I you getting kicked out for no cage!!!
 
D

denny

Active member
Re: How not to run 30psi boost! - Video added!

autoaddictions said:
Thanks for postin your runs is nice to watch sombody else beat ther truck. 11.5s is no joke for your mods. Your intake temps are sweet you must be using meth mine are 200*plus. I too am going to install meth soon. You go any faster, just like Ralph and I you getting kicked out for no cage!!!
Click to expand...

Thanks, yes meth, well windsheild washer fluid.
I would be happy to get kick out for runing 10s :D
 
mrweelr

mrweelr

New member
Re: How not to run 30psi boost! - Video added!

That 10-sec Ty is sick...love the 4-wheel burnout :tup:
 
You must log in or register to reply here.
Top