Search results

Re: Brodix Heads - Priced to sell! sold!!!

Re: Brodix Heads - Priced to sell! Replied.

Re: Brodix Heads - Priced to sell! Mike sells these heads, just not ported, etc... So I would guess they got something that will work... Like I said earlier, the price for his heads are $3,700... These are easily worth $4,000... Good buy here folks, I no longer have Syclone #411... Need to...

Re: Brodix Heads - Priced to sell! Thanks for the replies. They're 23 degree heads with angle plugs, so you'll need headers. Lower vortec in take and upper plenum will work fine. I promise you, you will not find a better set of heads for your truck this price, expect to pay probably 4 grand...

Re: Brodix Heads - Priced to sell! Make me an offer!!!

Re: Brodix Heads - Priced to sell! These heads have to go! These will out flow a ported vortec head by 30+ cfm, and you're getting them for around the same price. http://www.ebay.com/itm/320982323403?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649#ht_1223wt_1139 Need to sell these quick!

Since I sold my Syclone, no need for these to be sitting around. Just recently purchased from another SYTY member. These heads are MINT! Priced to sell and sell quick! If you don't like my price, PM me with a reasonable offer. Lil Brodie ALUMINUM Heads, Ported and rebuilt with all new parts by...

Re: FS: Syclone #411 - Price Drop!!! Trucks Sold!

Re: FS: Syclone #411 - Price Drop!!! Price Reduced. 12K

This is the truck I bought from T-Bone. I was injured in a car accident the week prior to picking the truck up and I'm in tough shape both physically and financially. Truck was recently tuned by Morgan @ www.synapseturbo.com Shaun will vouch for this truck. 1991 GMC Syclone Modified! $12,000...

Re: vanity plates I just got: BAD91GMC

Re: Syclone #411 Dyno Vid 19 degrees advanced 93 + Methanol The truck is making the power RPM says it should with their turbo upgrade. Next up is the ported brodie heads and a 67mm turbo.

Re: Syclone #411 Dyno Vid I'll get them both tomorrow.

Re: Syclone #411 Dyno Vid Yeah, I'll post one up tomorrow. The truck had to be fine tweaked on the street so I pick it up tomorrow. My curve was flat and then tapered off due to crappy flowing L35 heads!!!!

Here's a quick vid of my truck on a Dyno Dynamics AWD dyno. Trucks running 19 PSI with the RPM Stage 2 turbo. I ran out of compressor. @ 2600 RPMS the truck made a tad bit over 300 horse and 480 ftlbs of torque. I've never seen a curve on a dyno as linear as this one. http://youtu.be/Me44jKhTnE4

Re: High lb RPM wastegate Actuator You'll be able to make one no problem.

Re: High lb RPM wastegate Actuator The bracket we built looks similar to this, although I don't think this one will work. http://www.atpturbo.com/mm5/merchant.mvc?Screen=PROD&Store_Code=tp&Product_Code=ATP-WGT-027&Category_Code=WGT We took a washer that fit perfectly over the actuator, and...

Re: High lb RPM wastegate Actuator I didn't even look at the brackets... Let me look there and they might have one. I'll post back in a few minutes!

Re: High lb RPM wastegate Actuator Rod length wasn't a problem at all. Had to make a bracket to bolt to the housing. Only took about 1.5hrs to disassemble, make the bracket and re-assemble.

Re: High lb RPM wastegate Actuator Will do.