Parts and Cost of a SyTy Clone

dgoodhue

dgoodhue

BuSTeD 4.3
Here a list of unique part for Syclone and Typhoon and what would be needed a complete clone. You will need a 4wd frame to do the AWD conversion.

Cladding

Syclone and Typhoon have 14 pieces of cladding,

-Front Bumper (Shared between Sy/Ty/SoGt)
-Front Bumper Support
-Front Arches (2) (Shared SyTy)
-Door Cladding (2) (Shared SyTy)
-Rocker Cladding (2)
-Foward Rear Quarter/Bed (2)
-Rear Arches (2)
-Rear Corners (2) These pieces are particular rare for Ty's
-Rear Bumper Cover (Shared Between SyTySoGt)
-Rear Bumper Support

-Front and rear frame brackets,
-Door Mounting Cups (12) and brackets (6)
-Rocker Mounting Brackets (6)
-Rear Quarter Hangers/Cups (Ty) or Sy Bed Cups (12)
-Syclone/Typhoon Stickers

Interior

-Seats
-Steering Wheel
-Door Panel Inserts
-Center Console
-Shifter Assembly
-Dash Cluster
-Cluster Housing
-Cluster Mount Brackets
-Cluster Harness
-SyTy Glove Box Emblem

Suspension/Wheel

- 16 x 8 Wheels, Center Caps, and Locks
-Different Torsion Bar Rates (probably could be skipped on clones)
-Lowering Torsion bar pork chops
-Rear Lowering Springs (I would use Belltech lowering spring instead)
-ELC (Ty only, Electronic Level Control), I would skip this pump, tubing, bracket, wiring harness, air shocks. The ELC also uses a fuse box with a ELC fuse.
-Shocks

Driveline

-Front Differential Tube (could be ommited on clone)
-Front Propshaft
-AWD Transfer Case
-Transfer Case Brace
-SyTy Transmission
-Transmission Crossmember
-Shifter Cable and brackets
-Throttle to TV Cable
-Torque Converter
-Rear Driveshaft

Engine

-Air Box
-Intake Crossover Tube
-90 degree Orange Turbo Inlet hose
-Turbo
-Turbo Oil and Coolant lines
-Intercooler (Upper Intercooler, Low Heat Exchanger, Water Pump and lines)
-Intercooler Brackets (3)
-Exhaust Manifolds
-Down Pipe and Catback Exhuast
-Upper and Lower Intake manifold
-Throttle Body
-Transmission/Cruise Bracket
-Engine with Low Compression Pistons, different Head Gaskets and Nodular Main Caps
-Fuel Rail and Lines
-Injectors
-Better Fuel Pump
-749 ECM
-ECM Wiring Harness
-Coil/MAP/EGR Brackets
-Knock Sensor
-Dual PCV Pipe

Misc Engine Compartment

Fog lights and foglight Harness
Battery Cables
Battery Tray (S-Series can be trimmed)
Heater Hoses/Pipe
IC Over Flow Bottle
ABS Brakes (I would skip this as the ABS prone to failure)
 
Last edited:
dgoodhue

dgoodhue

BuSTeD 4.3
Re: Parts and Cost of a SyTy Clone

I started doing a list, I know I am missing a few pieces. I haven't even gotten around to doing the prices. Feel Free to give your input to missing parts and give pricing. Have fun with it. I will update the first post as need and if comes out well and nobody objects I will make it sticky.
 
dgoodhue

dgoodhue

BuSTeD 4.3
Re: Parts and Cost of a SyTy Clone

I want to say one of the Radiator Hoses is unique and the other is a standard S-10 part. I am not sure about the remote oil cooler lines.
 
phoonTy

phoonTy

Truckless. For now.
Re: Parts and Cost of a SyTy Clone

Nice! :tup:

I guess if someone was going to do an exact clone, you could add the ELC/Auto Leveling parts to the list as well. Not that anyone would actually use them, but it would complete the list... or at least help fill it out.
 
jjorgensen52

jjorgensen52

NHSTE - I'm the only one!
Re: Parts and Cost of a SyTy Clone

dgoodhue said:
I want to say one of the Radiator Hoses is unique and the other is a standard S-10 part. I am not sure about the remote oil cooler lines.
Click to expand...
remote cooler lines are normal. IIRC the upper radiator hose is the oddball one
 
ShuggsRR

ShuggsRR

Donating Member
Re: Parts and Cost of a SyTy Clone

Hmmm Thanks for the list... Neat checklist for me.

- Core support stickers are SyTy specific. I have a stock 92 Ty core support for mine with stickers intact.
- Door jamb sticker is SyTy specific.

My 85 doesnt have shoulder belts in the rear. So I have to custom work the seats and side panels.
My 85 doesnt have a barcode on the VIN plate. Its a metal colored VIN tag and a SyTys is black.

my Tyclone has the following....
Red = have it
Yellow = have/had it but opted to change out
Orange = dont have/not using

-Front Bumper (Shared between Sy/Ty/SoGt)
-Front Bumper Support
-Front Arches (2) (Shared SyTy)
-Door Cladding (2) (Shared SyTy)
-Rocker Cladding (2)
-Foward Rear Quarter/Bed (2)
-Rear Arches (2)
-Rear Corners (2) These pieces are particular rare for Ty's
-Rear Bumper Cover (Shared Between SyTySoGt)
-Rear Bumper Support
-Front and rear frame brackets,
-Door Mounting Cups (12) and brackets (6)
-Rocker Mounting Brackets (6)
-Rear Quarter Hangers/Cups (Ty) or Sy Bed Cups (12)
-Syclone/Typhoon Stickers - Custom Tyclone stickers made

-Seats
-Steering Wheel Sold it for a Grant GT wheel.
-Door Panel Inserts
-Center Console
-Shifter Assembly
-Dash Cluster Sold it for a Sonoma GT one
-Cluster Housing
-Cluster Mount Brackets
-Cluster Harness
-SyTy Glove Box Emblem

- 16 x 8 Wheels, Center Caps, and Locks - Got 18" C5 wagon wheels
-Different Torsion Bar Rates (probably could be skipped on clones) I didnt know that.. damn
-Lowering Torsion bar pork chops Use a Bell Tech torsion key
-Rear Lowering Springs (I would use Belltech lowering spring instead) Used BellTech
-ELC (Ty only, Electronic Level Control), I would skip this pump, tubing, bracket, wiring harness, air shocks. The ELC also uses a fuse box with a ELC fuse. Had one but threw it out
-Shocks KYB Monomax up front and Bilstein in the rear

-Front Differential Tube (could be ommited on clone) Whats that?
-Front Propshaft
-AWD Transfer Case
-Transfer Case Brace
-SyTy Transmission 4L60e
-Transmission Crossmember
-Shifter Cable and brackets
-Throttle to TV Cable Nope
-Torque Converter 2000 stall
-Rear Driveshaft

-Air Box
-Intake Crossover Tube
-90 degree Orange Turbo Inlet hose
-Turbo
-Turbo Oil and Coolant lines
-Intercooler (Upper Intercooler, Low Heat Exchanger, Water Pump and lines)
-Intercooler Brackets (3)
-Exhaust Manifolds
-Down Pipe and Catback Exhuast
-Upper and Lower Intake manifold
-Throttle Body
-Transmission/Cruise Bracket
-Engine with Low Compression Pistons, different Head Gaskets and Nodular Main Caps
-Fuel Rail and Lines
-Injectors
-Better Fuel Pump
-749 ECM
-ECM Wiring Harness
-Coil/MAP/EGR Brackets
-Dual PCV Pipe

Fog lights and foglight Harness
Battery Cablesrelocated to rear
Battery Tray (S-Series can be trimmed) relocated to rear
Heater Hoses/Pipe
IC Over Flow Bottle
ABS Brakes (I would skip this as the ABS prone to failure)
 
Timbo

Timbo

SyTy Stalker
Re: Parts and Cost of a SyTy Clone

ShuggsRR said:
-Front Differential Tube (could be ommited on clone) Whats that?
Click to expand...
I assume he's referring to the vent tube that goes from the front diff up into the engine bay. I believe it's attached to the firewall on the driver's side.
 
jjorgensen52

jjorgensen52

NHSTE - I'm the only one!
Re: Parts and Cost of a SyTy Clone

Loeryder said:
power mirrors and harness for Tys
Click to expand...

Standard to all S-series trucks with power mirrors. Mostly Bravadas and Jimmys 93 and 94
 
ShuggsRR

ShuggsRR

Donating Member
Re: Parts and Cost of a SyTy Clone

jjorgensen52 said:
Standard to all S-series trucks with power mirrors. Mostly Bravadas and Jimmys 93 and 94
Click to expand...
Not 85s though.... sigh... :rant:
 
dgoodhue

dgoodhue

BuSTeD 4.3
Re: Parts and Cost of a SyTy Clone

Timbo said:
I assume he's referring to the vent tube that goes from the front diff up into the engine bay. I believe it's attached to the firewall on the driver's side.
Click to expand...

The 4X4 front differential can be engage and disengage, while SyTy are always engage.
 
$Hot-Rod$

$Hot-Rod$

New member
Re: Parts and Cost of a SyTy Clone

dgoodhue said:
I started doing a list, I know I am missing a few pieces. I haven't even gotten around to doing the prices. Feel Free to give your input to missing parts and give pricing. Have fun with it. I will update the first post as need and if comes out well and nobody objects I will make it sticky.
Click to expand...
Don't forget the most important part- Jackstands. :rant:
 
S

s_blazin

Donating Member
Re: Parts and Cost of a SyTy Clone

i am wanting to make my v8 s10 awd with syclone interior, any tips?

if bravada awd is the same i can have that area covered and i have an interior harness from a SGT with cluster, but i need the brackets on the floor for seats and center console, (as seen in my sig)
 
sytyguy

sytyguy

Moderated User
Re: Parts and Cost of a SyTy Clone

Knock sensor is SyTy specific. BTW, the radiator hoses are standard S-Series issue, just for somewhat later models ('94, '95, etc...).
 
BoostedSUV

BoostedSUV

Active member
Re: Parts and Cost of a SyTy Clone

sytyguy said:
Knock sensor is SyTy specific. BTW, the radiator hoses are standard S-Series issue, just for somewhat later models ('94, '95, etc...).
Click to expand...
are you refering to the upper or lower rad hose? Found this thread by accident and I need a lower ASAP
 
FxsX24

FxsX24

94 S10 to be lowered/v8
Last edited:
leadfoot

leadfoot

Member
Re: Parts and Cost of a SyTy Clone

A newer generation radiator will not fit an older gen rad support. Newer rads have "pins" which go into rubber grommets. Try to get the same generation radiator.
 
leadfoot

leadfoot

Member
Re: Parts and Cost of a SyTy Clone

dgoodhue said:
I want to say one of the Radiator Hoses is unique and the other is a standard S-10 part. I am not sure about the remote oil cooler lines.
Click to expand...


Re: Oil cooler. I had to convert to all rubber lines and re route/mount in second gen engine compartment. (2002)
 
You must log in or register to reply here.
Top